An Adventure Back In Time: What People Discussed About Fix Door Hinge 20 Years Ago > 자유게시판

How to Fix a Loose Door Hinge

Fixing a loose door hinge can be a doable job for the majority of homeowners. If the holes for screws have been stripped and will not hold screws, you may need to use dowels and wood glue to fix the hinge.

Before you do that, however, brush away the surface corrosion. This will aid in keeping the dowels in place and provide a solid base for them to rest on.

Removing the Hinges

A lot of door hinges can be removed, which makes it easier to move the door from one side to the next or to take the entire door off of the frame, if needed. Removing the hinges is fairly simple for anyone with a bit of patience, though you do have to know how to do it right.

If the hinges have been painted, you'll need to remove the paint before you attempt to remove the pins. If you don't, the paint will be smashed off and scratch your door when you try to lift it. To break the seal of the paint, place the hinges in an stainless steel pan and fill the pan with water until the hinges are completely submerged. Let the hinges sit in the pan for around 30 minutes. The heat of the water will soften the paint making it easier to take off.

After the pins are loosening then you can remove the hinges from the door and frame. It is possible to use a standard screwdriver, but it is recommended to use a magnetic screwdriver for this task. This type of screwdriver is specifically designed to take out screws made of metal and will assist you in getting the task accomplished much faster.

It is a good practice to spray some lubricant on the hinges prior to trying to remove them. A simple lubricant will allow you speed up the process and also remove the screws and pins easier. You can find this type of lubricant at a variety of hardware and home improvement stores.

The number of hinges needed will also differ based on what type of door you have and the way it's installed. Heavier and solid-cored Bifold Doors Hinges will require more hinges, whereas hollow-cored and lighter doors might only require two or three hinges.

It is also crucial to know the various types of hinges so you can determine which ones work best in your situation. Exterior hinges are generally designed to support the door's weight, while interior hinges will need to be able to handle heavier loads.

Reattaching the Hinges

Sometimes a door hinge will become looser over time and begin to hang in a crooked manner or sag. This can be a problem but is usually easy to repair window hinges. Retightening the screw will typically resolve the issue. If the screw holes have been stripped out, it may be difficult to do. A wood dowel could be used to tighten the holes again.

Begin by drilling out the hole from the previous one using a drill bit that is similar to the size of the new screw (typically 3/8"). Fill in the hole with wood glue and a wooden stick. To ensure a snug fit, the dowel must be cut at the same length as the screw. Then, you can reinstall the screw and tighten it until the desired degree of tightness. If the door continues to bind up, insert a second dowel into the gap. Repeat the procedure. Close the door slowly after each adjustment to make sure that the perimeter clearances are in order.

Another option is to make use of an old-fashioned wood plug instead of a dowel. It's also possible however it will take some time to set up. Simply whittle a chunk of wood that is the appropriate size for a comfortable fit, and then insert it into the hole. If you don't have an instrument for woodworking, you can use toothpicks or wooden matchsticks.

Once you have reinstalled the new screw then use a countersink to make the hole for the screw's head smaller so that it won't be able to rub against the edge of the door when it's opened and closed. This will make it much easier to tighten the screws after reinstalling hinges.

Once you've reinstalled your hinge, be sure to grease it using a dry lubricant to ensure that it doesn't get stuck in the future. You can use products such as PB Blaster and Liquid Wrench. Apply a thin layer and allow it to penetrate the barrel of the hinge for approximately 15 minutes.

Refinishing the Hinges

If you're not sure if you're ready to replace the hinges on your door hinge repairs, you can make a few minor repairs. Check that the screws that secure the hinge plate to the door frame and the frame are tight. If they're loose, tighten the screws with a power drill or screwdriver. Be cautious not to tighten the screws to the point that they start to cause gaps at the trim joints or, even more damagingly, strip the threads.

If the issue is that the hinge plates are breaking they can be reattached to the plates by putting wood glue to the side of them and inserting wooden dowels or toothpicks in the holes. Dowels or toothpicks will serve as a solid base for the screws and keep the plates from moving when you drive them into the holes. Let the glue dry before attaching the hinge.

The screws could also be smashed or gone. This issue can be resolved by replacing the screws. Make sure you use a drill bit that matches the size of the screw hole to avoid drilling into other parts of the jamb or hinge.

Close the door once you've reattached your hinge and measure the gap between the frame and the door. The gap should be the thickness of a penny or less if the old door was hung incorrectly. If the hinges were put in place correctly, this should not be an issue.

If the hinges are still loose, you can add an extra thick hinge between the surface of the hinge plate and the mounting surface. This will give the hinges more space. You could also try taking the hinge pin from the problematic hinge and then pounding it with a hammer in order to make it tighter or use a new hinge pin altogether. It is also possible to lubricate the hinges with mineral or jojoba oil to lessen friction and aid in holding their position. Lubricating your hinges regularly can prevent them from becoming stiff and squeaky and also prolong their lifespan.

Cleaning the Hinges

The constant movement of a hinge causes friction, which attracts dust particles. If there is no regular cleaning or lubrication, these particles get stuck in the moving parts of a hinge for upvc doors hinges and build up over time. In the end the hinge becomes stiff and creaky and its appearance could be damaged quickly. Regular cleaning, lubrication, and inspection can preserve the quality of hinged door repairs door and ensure their proper operation.

Inspect the hinges to see how much rust has built up on their surface. If the rust has become so severe that it has damaged the surface of the screw holes or the barrel of the hinge, you'll have to replace them. If you're able to save the hinges, remove any loose rust using wire brush and steel wool. Apply a commercial rust-removing solution or homemade solutions like lemon juice on the hinge. Let the rust remover be on the hinge for a few minutes to dissolve and penetrate any remaining corrosion.

If you do not want to spend time and money to replace hinges, tightening the screws will make the hinges functional again. If you have stripped the screws, however, it may be necessary to attach an wooden dowel or shim to the hinge. Wooden dowels are round pieces made of wood in the shape of rods which are available in various lengths and sizes. They are available at home improvement centers as well as woodworking supply and craft shops, or online.

A shim could be made of plastic or metal, depending on the kind of hinge you have. To make a dowel cut a dowel from wood to the desired length. You can then dip the dowel in carpenter's glue before inserting it into the stripped hole, allowing the glue to hold the dowel in the desired position.

Before cleaning the hinges, put down a piece of paper cloth or towel to protect your flooring from spills. Once the area is protected then clean the hinges using an absorbent sponge or a soft cloth that has been soaked in mild cleaner or vinegar to remove the build-up of dirt, grime and tarnish. A small brush or toothbrush can be used to access difficult-to-reach places in crevices and narrow spots.